CAB Apollo 1 Spezifikationen Seite 184
- Seite / 234
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Maintenance and Registering
D/38
Mod. Apollo
- ATTENTION: - Read the SAFETY REGULATIONS (contained in this manual) carefully for the safety of all personnel and your vehicle.
(fig.82/D)
(fig.83/D)
(fig.84/D)
(fig.85/D)
1
2
1
C3
2
3
2
3
1
LIGHTING
Vehicle lighting must always be efficient and functioning prop-
erly. Proper lighting function must be checked daily. If the light-
ing body is damaged in any way, replace the damaged part
immediately. Burnt light bulbs should be replaced immediately.
FRONT LIGHT
(fig.82/D)
The front light is composed of a direction indicator, a posi-
tion light, dipped light/headlight.
To access the bulbs:
- Switch off the vehicle and use the battery isolator to cut-
out electrical power.
- Remove the power connection of the rear light.
- Remove the front part of the light by loosening its screws
located in the rear cap.
To close the light back up, carry out these steps in the oppo-
site order, being careful to position the seal correctly.
Replacing direction indicator bulbs
(fig.83/D Pos.”1”) (21w)
- Press the upper part of the bulb.
- Turn and hold down the bulb to free it from the lock.
Carry out the same steps to insert the new bulb.
Replacing position light bulbs
(fig.84/D Pos.”1”) (4w)
- Take hold of the rear part where the electrical connec-
tions are located (fig.84/D Pos.”2”).
- Turn and pull the rear part towards you.
- Remove the support and press the upper part of the bulb.
- Turn and hold down the bulb to free it from the lock.
Carry out the same steps to insert the new bulb. Reinsert
the support inside its housing.
Replacing a dipped light/headlight bulb
(fig.85/D Pos.”1”) (60/55w H4)
- Remove the electrical connector by pulling it towards you.
- Raise the locking tabs (fig.85/D Pos.”2”), moving them
laterally to free the bulb.
- Replace the bulb and proceed in the opposite order to
lock and reconnect it. Respect bulb closing mechanisms
(fig.85/D Pos.”3”) for proper insertion.
- ATTENTION -
The bulbs are very fragile. Handle them with care.
The dipped beam bulbs must not
be handles with bare hands.
- MAINTENANCE MANUAL 1
- OPERATION AND 1
- Cod.: AXH1147/UK 3
- CHAPTER “A” 5
- CHAPTER “B” 5
- CHAPTER “C” 7
- CHAPTER “D” 7
- MAINTENANCE AND REGISTRATION 7
- Mod. Apollo 10
- GUARANTEE 11
- VEHICLE IDENTIFICATION 11
- INTRODUCTION 11
- FAC-SIMILE 19
- SAFETY REGULATIONS 21
- - DANGER 22
- - WARNING 22
- - PROHIBITION 22
- - NOTE 22
- GENERAL WARNINGS 23
- PREPARATION FOR EMERGENCIES 25
- DRIVER’S CAB 27
- STARTING UP THE VEHICLE 29
- ENVIRONMENTAL CONDITIONS 29
- - ATTENTION 31
- PARKING THE VEHICLE 35
- TEMPORARY HALT 35
- HOISTING THE MACHINE 37
- TRANSPORTING THE MACHINE 37
- CLEANING YOUR MACHINE 41
- FIRE PREVENTION 43
- TIGHTENING WHEEL NUTS 47
- STORING DANGEROUS FLUIDS 49
- CONTACT WITH DANGEROUS FLUIDS 49
- ROPS-FOPS CAB 59
- BAR 4,5BAR 4,5 69
- AXA 1506 71
- DEXTRON 2 71
- AXA 1492 71
- GETTING TO KNOW AND 73
- USING THE VEHICLE 73
- HAND SIGNALS 77
- External cab components 79
- Internal cab components 79
- INTERIOR CAB INSTRUMENTS 87
- I CELL 89
- MULTI-FUNCTION LEVER 95
- I CE 97
- SERVICE CONTROL LEVER 101
- - ATTENTION: 101
- Proportional services 103
- Alarm re-entry push button 105
- VEHICLE FUNCTIONS SELECTOR 107
- REVOLVING LIGHT SWITCH 113
- BOOM HEAD SOLENOID VALVE 115
- (OPTIONAL) 115
- FRONT HOOK 119
- AXA 1432 122
- USER INSTRUCTIONS AND 131
- GETTING TO KNOW THE VEHICLE 131
- INTEGRATED DEVICES 131
- “CENTRAL DASHBOARD” 131
- 891211 7 6 133
- I CEL 135
- (fig.207/C) 139
- (fig.208/C) 139
- ERRORS LIST 141
- Description What to do 145
- MAINTENANCE AND 147
- REGISTRATION 147
- MAINTENANCE PRESCRIPTIONS 149
- MANUFACTURER 151
- IDENTIFYING THE VEHICLE PARTS 153
- DO NOT USE 158
- SYNTHETIC-BASED OIL 158
- PARKING BRAKE 161
- Epicycloidal reduction gear 175
- (fig.57/D) 177
- (fig.69/D) 181
- 4.8 5.8 6.8 8.8 10.9 12.9 186
- 60° oval insert - BSP thread 188
- TROUBLESHOOTING 189
- TROUBLE SHOOTING 191
- MACHINE DETAILS 193
- AND MAINTENANCE WORK 195
- - ATTENTION 197
- ELECTRICAL DIAGRAMS 207
- AND CIRCUITS 207
- NAME DESCRIPTION SHEET 209
- WIRE COLOURS 213
- Valid certified 215
- HYDRAULIC CIRCUIT 223
- DIRECTIVE “ 225
- HYDRAULIC PLANT KEY 227
- TECHNICAL DATA 229
- TECHNICAL FEATURES 229
- Apollo 25.6 230
- (in seconds) 231
Verwandte Produkte und Handbücher für Etikettendrucker CAB Apollo 1
Etikettendrucker CAB A8+ Betreibershandbuch
(120 Seiten)
(120 Seiten)
Etikettendrucker CAB A8+ Bedienungsanleitung
(11 Seiten)
(11 Seiten)
Etikettendrucker CAB a2+ Bedienungsanleitung
(6 Seiten)
(6 Seiten)
Etikettendrucker CAB MACH4 Bedienungsanleitung
(12 Seiten)
(12 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern